Lyophilization is one of those subjects where the details matter more than the headlines. This page pulls together the background, the mechanisms, and the practical points readers ask about most.
Last reviewed on 2026-08-01. Where a claim depends on a specific study, the study is described rather than over-claimed.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and fixes the structure of the sample. After freezing, primary drying lowers pressure so ice changes directly to vapor without passing through a liquid phase. Secondary drying then removes bound water that remains after ice sublimation. The result is a dry, porous solid that often retains its original shape.
The low pressure used during drying allows water vapor to move from the ice surface to a cold condenser. Energy supplied as heat drives sublimation but must stay below the collapse temperature of the frozen matrix. If the product becomes too warm, the frozen structure may soften or melt, reducing pore formation and slowing drying. Formulations often include bulking agents, stabilizers, or buffers to support a rigid cake. The final moisture content depends on formulation, freezing rate, and the length of secondary drying.
Lyophilization removes water by freezing a material and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intermediate liquid state. Because the material remains frozen during primary drying, the structure often stays porous. This porous matrix can rehydrate quickly when water is added back. The low pressure also allows vapor to leave the solid matrix without boiling.
A typical cycle begins with freezing, which fixes the material into a solid and determines ice crystal size. Primary drying then raises heat under vacuum so ice sublimes, often near or below the collapse temperature of the formulation. Secondary drying removes bound water that remains after ice is gone, usually by gently warming the product. Each stage balances heat input against pressure to avoid melting or structural damage. Temperature probes and pressure sensors guide the transition between stages.
In practice, lyophilization is slower and more energy intensive than simple drying. Cycle times can range from hours to several days depending on load, container, and formulation. Amorphous materials may require excipients that help preserve structure during freezing and drying. The method is widely used for biological materials, pharmaceuticals, and foods where heat drying would cause unacceptable change. Open questions remain about scaling cycles between laboratory and production equipment, and this gap affects technology transfer.
| Property | Value | Notes |
|---|---|---|
| Primary phase change | Sublimation | Ice changes directly to vapor under reduced pressure |
| Typical chamber pressure | 0.01–0.5 mbar (1–50 Pa) | Below the triple point of water; product-specific |
| Typical product temperature during primary drying | −40 °C to −10 °C | Kept below collapse temperature |
| Typical residual moisture | 0.5–3% w/w | Target range varies by formulation and use |
| Common synonyms | Freeze-drying; lyophilisation | Lyophilization is the US spelling |
Lyophilization, also known as freeze-drying, is a process that removes water from a material by freezing it and then reducing pressure to allow ice to sublimate directly into vapor. The method begins with a freezing step that solidifies the water content. Next, primary drying lowers the pressure below the triple point of water, enabling sublimation without passing through a liquid phase. A final secondary drying step removes bound water through desorption. This sequence produces a dry, porous cake that can be reconstituted later.
The process relies on the phase diagram of water, where the triple point marks the conditions at which ice, liquid water, and vapor coexist. By maintaining pressure below this point, typically around 0.01 to 0.1 millibar, sublimation becomes the dominant mechanism. Formulations often include excipients such as sugars or polymers that act as lyoprotectants and bulking agents. These additives help preserve the structure of the active ingredient and prevent collapse during drying. The choice of excipient and freezing rate influences the final cake morphology and stability.
The physics of lyophilization depends on phase boundaries and heat and mass transfer. During primary drying, heat supplied to the product must equal the latent heat of sublimation, while water vapor moves through the drying cake to the condenser. If shelf temperature or pressure is set too high, the ice front can exceed the collapse temperature, causing meltback or pore collapse. If conditions are too cold, drying slows and costs rise. Formulation excipients, vial geometry, and freezing rate alter these limits.
Equipment for lyophilization includes a vacuum chamber, temperature-controlled shelves, a condenser, and a vacuum pump. A refrigeration system cools the shelves and condenser below the product's freezing point. Process monitoring often uses Pirani and capacitance manometers, thermocouples, and resistance sensors. Cycle development balances product quality with time and energy use. Some products are annealed during freezing to improve crystallization of bulking agents. Open questions remain about scaling cycles between laboratory, pilot, and production freeze-dryers.
Secondary drying removes bound water that remains after ice sublimation. Shelf temperature is raised gradually while pressure remains low, reducing water content to a target range. Over-drying can cause brittleness or electrostatic issues, while under-drying affects stability. The endpoint is often judged by pressure rise tests, temperature measurements, or water content analysis. Scale-up depends on matching heat and mass transfer across equipment sizes. Small changes in shelf temperature or pressure can alter cycle length substantially.
Lyophilization, or freeze-drying, removes water from a material by freezing it and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intervening liquid state. It is used for heat-sensitive materials that would degrade in conventional drying. The three stages are freezing, primary drying, and secondary drying, each with distinct temperature and pressure requirements. In practice, cycle design balances these variables.
Freezing determines ice crystal structure and pore size, which affect drying speed and product uniformity. Rapid freezing creates small crystals, while slow freezing creates larger crystals and often faster sublimation. During primary drying, chamber pressure is held below the vapor pressure of ice, and shelf temperature supplies heat for sublimation. The ice front recedes, leaving a porous matrix. Thermal limits such as collapse and eutectic temperatures set safe boundaries for formulation. These limits vary with solute composition and concentration.
The physics of lyophilization couples heat transfer, mass transfer, and phase behavior. Sublimation requires a vapor pressure difference between the ice front and the chamber, and the dried layer adds resistance to vapor flow. Amorphous formulations are characterized by a glass transition temperature of the maximally freeze-concentrated solute, often denoted Tg'. Crystalline bulking agents can provide structure, while amorphous excipients stabilize labile components. Open questions remain about spatial heterogeneity, edge effects, and how laboratory cycles scale to production.
Lyophilization is a drying process in which a solvent, usually water, is removed from a frozen material by sublimation under reduced pressure. The material is first solidified, then placed under vacuum so that ice transitions directly to vapor without a bulk liquid phase. This approach suits heat-sensitive substances that would degrade during conventional evaporation. Primary drying removes unbound ice, while secondary drying reduces water that remains adsorbed to the solid matrix. The result is a porous, lightweight solid that can be reconstituted later.
24 November – Colin Renfrew, Baron Renfrew of Kaimsthorn, 87, British archaeologist, academic and peer, member of the House of Lords (1991–2021). 1 December – Sir Richard Carew Pole, 13th Baronet, 85, British aristocrat. 2 December – Rosalie Wilkins, Baroness Wilkins, 78, British politician, member of the House of Lords (1999–2015). (death announced on this date) 8 December – Tony Lloyd, Baron Lloyd of Berwick, 95, British jurist, lord of appeal in ordinary (1993–1998), member of the House of Lords (1993–2015). 15 December – Andrew Bennett, 85, British politician, MP (1974–2005). 18 December – Patrick Conolly-Carew, 7th Baron Carew, 86, Irish equestrian and aristocrat, Member of the House of Lords as a hereditary peer (1994–1999).
=== Awards === One of Time magazine's 100 most influential people in 2019 and 2020 Brazilian-American Chamber of Commerce's 2019 Person of the Year OCCRP's 2020 Person of the Year "for his role in promoting organized crime and corruption" On 25 October 2021 he was recognized as an honorary citizen by the city council of Anguillara Veneta, Italy, his paternal grandfather's hometown. This aroused reactions in Italy.
It is thought that high glucagon levels and lack of insulin production are the main triggers for the metabolic issues associated with Type I diabetes, in particular maintaining normal blood glucose levels, formation of ketone bodies, and formation of urea. One finding of note is that the glucagon response to hypoglycemia is completely absent in patients with Type I diabetes. Consistently high glucagon concentrations in the blood can lead to diabetic ketoacidosis, which is when ketones from lipid breakdown build up in the blood, which can lead to dangerously low blood glucose levels, low potassium levels, and in extreme cases cerebral edema. It has been proposed that the reason for the high levels of glucagon found in the plasma of patients with Type I diabetes is the absence of beta cells producing insulin and the reciprocal effect this has on delta cells and the secretion of somatostatin.
Sources: en.wikipedia.org
The Israelites, also known as the Children of Israel, were an ancient Semitic-speaking people who lived in Canaan during the Iron Age. They are associated with Hebrews and spoke Biblical Hebrew, an archaic Hebrew language. In the biblical myth, the Israelites were divided into the Twelve Tribes of Israel and later formed the Iron Age kingdoms of Israel and Judah. Modern scholarship describes the Israelites as emerging from indigenous Canaanite populations and other peoples of the ancient Near East. The Israelite religion revolved around Yahweh, who was an ancient Semitic god with less significance in the broader Canaanite religion. Around 720 BCE, the Kingdom of Israel was conquered by the Neo-Assyrian Empire, triggering the Assyrian captivity; and around 586 BCE, the Kingdom of Judah was conquered by the Neo-Babylonian Empire, triggering the Babylonian captivity. While most of Israel's population was irreversibly dispossessed as a result of Assyrian resettlement policy, the exiled Judahites were allowed to return and rehabilitate their country by the Achaemenid king Cyrus the Great following the fall of Babylon in 539 BCE. In the narrative of the Hebrew Bible, the Israelites were the descendants of Jacob (later known as Israel), who was a son of Isaac and thereby a grandson of Abraham. Due to a severe drought in Canaan, Jacob and his twelve sons migrated to Egypt, where each son became the eponymous progenitor of an Israelite tribe.
== Mechanism of action == Nalfurafine is an orally active, centrally acting, highly potent, selective full agonist of the κ-opioid receptor (KOR) (Ki = 75 pM; EC50 = 25 pM). As touched on above, nalfurafine shows atypical properties as a KOR agonist relative to other drugs. Notably, it does not completely substitute for the prototypical KOR agonist U-50488 in rodents, indicating qualitative differences in the discriminative effects of the two compounds. Moreover, unlike U-50488, it produces neither conditioned place aversion or preference in rodents. The drug is a 4,5-epoxymorphinan derivative, and is structurally unique relative to other KOR agonists. Nalfurafine may be a biased agonist of the KOR or a KOR subtype-selective agonist. Indeed, it has been found to act as a biased agonist of the KOR, preferring activation of β-arrestin signaling in vitro, but paradoxically, β-arrestin appears to be responsible for KOR agonist-induced aversion, and nalfurafine furthermore shows paradoxical effects in vivo that are not consistent with its in vitro profile. As such, more research is needed to clarify the distinct mechanisms and effects of this drug. Nalfurafine has been found in vitro to bind to the μ-opioid receptor and to possess weak partial agonist activity at this site, albeit with much lower affinity relative to the KOR. However, in vivo, nalfurafine has shown no indications of MOR agonism or antagonism in animals or humans, including no evidence of rewarding or reinforcing effects or physical dependence.
Neanderthals, probably uncommonly, buried their dead. This may explain the abundance of fossil remains. The behaviour is not indicative of a religious belief of life after death because it could also have had non-symbolic motivations. The dead were buried in simple, shallow graves and pits, but special care seems to have been given to child graves. The graves of children and infants, especially, are associated with grave goods such as artefacts and bones. Some sites with multiple well-preserved Neanderthal skeletons may represent cemeteries. One grave in Shanidar Cave, Iraq, was associated with the pollen of several flowers that may have been in bloom at the time of deposition—yarrow, centaury, ragwort, grape hyacinth, joint pine and hollyhock. The medicinal properties of the plants led American archaeologist Ralph Solecki to claim that the man buried was a leader, healer, or shaman, and that "the association of flowers with Neanderthals adds a whole new dimension to our knowledge of his humanness, indicating that he had 'soul'". It is also possible the pollen was deposited by a small burrowing rodent after the man's death. Neanderthals were once thought to have ritually killed and eaten cave bears or other Neanderthals, but the evidence is circumstantial. In 2019, the Finlaysons reported that Neanderthals disproportionately butchered the golden eagle over any bird of prey or corvid species, and speculated that Neanderthals viewed the golden eagle as a symbol of power like some recent modern human societies did.
Sources: en.wikipedia.org
“At some point, we will probably also have to pay for the embezzlement of the Itaipu Retirement Fund (Cajubi), which is another case, and that's because there isn't a public entity that is constitutionally obligated to do so,” he stated. On December 14, 2023, Peña enacted Law 7253/23, creating the Superintendency of Retirements and Pensions in Paraguay.
After surgery, a woman is instructed to restrict her activities and monitor herself for signs of infection such as an elevated temperature, discharge with a foul odor, and consistent pain. Clinicians may recommend that sneezing, coughing, and constipation be avoided. Splinting the abdomen while coughing supports an incised area and decreases pain with coughing. This is accomplished by applying gentle pressure to the surgical site for bracing during a cough. Recurrent surgery on the pelvic organs may not be due to a failure of the surgery to correct the cystocele. Subsequent surgeries can be directly or indirectly related to the primary surgery. Prolapse can occur at a different site in the vagina. Further surgery after the initial repair can be to treat complications of mesh displacement, pain, or bleeding. Additional surgery may be needed to treat incontinence. One goal of surgical treatment is to restore the vagina and other pelvic organs to their anatomically normal positions. This may not be the most important outcome to the treated woman, who may only want symptom relief and to improve her quality of life. The International Urogynecological Association (IUGA) has recommended that the data collected regarding cystocele and pelvic organ repair success include the presence or absence of symptoms, satisfaction, and Quality of Life. Other measures of a successful outcome should include perioperative data, such as operative time and hospital stay. Standardized Healthcare Quality of Life should be part of the measure of a successful resolution of cystocele.
== Management == Medical management of VHF patients may require intensive supportive care. Antiviral therapy with intravenous ribavirin may be useful in Bunyaviridae and Arenaviridae infections (specifically Lassa fever, RVF, CCHF, and HFRS due to Old World Hantavirus infection) and can be used only under an experimental protocol as IND approved by the U.S. Food and Drug Administration (FDA). Interferon may be effective in Argentine or Bolivian hemorrhagic fevers (also available only as IND).
The way our fellows charged their way along these paths, yelling, makes a lump come into my throat when I think of it even now. It was sheer suicide for the leading group and the whole force faced machine guns up the sides of the slopes above them, on the sides of the features behind them, and even up the trees above them, with snipers behind who let them pass before opening fire. For sheer cold-blooded bravery, I can't believe it has ever been beaten in any other theatre of war; and this went on for three weeks solid. 1RAR spent most of May 1945 building quarters and training before marching the 110 km (68 mi) to Prome in late June; from here they went another 25 km (16 mi) by truck to Gyobingauk. The monsoon conditions took a dreadful toll on operations, making logistics particularly difficult and slow—men found themselves either found themselves knee-deep in mud or slipping around on the surface. From early July 1945 1RAR patrolled around Gyobingauk, repeatedly engaging parties of Japanese and forcing them into the hills. Even after the Japanese commanders in Burma surrendered unconditionally, the Allied troops had to continue patrolling to handle Japanese stragglers who either did know of this or did not believe it. After the Japanese forces in South-East Asia formally surrendered at Singapore on 12 September 1945, active Allied operations in the region were greatly diminished. 1RAR spent about half a year guarding Japanese prisoners in Burma before leaving for home in March 1946. They arrived back in Salisbury on 10 May.
Sources: en.wikipedia.org
Lyophilization relies on sublimation, so water moves from solid ice to vapor without becoming liquid. The material is frozen, pressure is reduced, and controlled heat is supplied. Vapor is captured on a cold condenser, leaving a dry porous solid.
The process has three main stages: freezing, primary drying, and secondary drying. Freezing sets the ice structure, primary drying removes free ice, and secondary drying removes bound water. Each stage uses specific temperature, pressure, and time settings.
No, it is a drying method rather than a sterilization method. Removing water can limit microbial growth, but it does not reliably kill microorganisms. Sterility must come from separate steps such as filtration, heat treatment, or aseptic processing.
Primary drying removes ice by sublimation under vacuum. Secondary drying removes water that is bound to the material, often by warming the product after most ice has left. Both stages occur below temperatures that would cause unwanted melting.